can you use powder in a front load washer?,for front-loading machines that use less water, a liquid homemade detergent seems to work more smoothly especially in an automatic dispenser. if you choose to use powdered detergent in a front load washer, add the two tablespoons directly to the drum before loading in the soiled laundry..how to stain concrete paving stones | doityourself.com,you can clean the concrete stones with soap and water but they do need to be dry prior to staining. surface scratches can be repaired by sanding them. deeper scratches, gouges, and chips can be repaired by using a concrete patch kit. once the concrete patch has dried you will need to sand it flush to the surface of the concrete paving stones..
What Can I Do For You?
for 80 years, durham's rock hard water putty has been making repairs in wood, plaster, drywall, stone, tile, concrete and other stable surfaces. just add water to this powdered material, apply it into voids, cracks and holes. when thoroughly dry, it can be sanded, drilled, sawed and painted.
professional installation of a flagstone walkway can cost $10-$25 or more a square foot for dry-set (on a bed of sand or gravel) and $20-$40 or more a square foot for wet-set one (mortared on a slab of reinforced concrete) , depending on local rates and the complexity of the project, or about $1,000-$2,500 for a dry-
when using a liquid bonding agent, paint the bonder onto the existing concrete and allow it to dry until it is tacky. this usually takes only a few minutes. then apply the repair material. just as in the process described above, after the bonder has become tacky apply
the concrete is at the right stiffness when the imprint depth is about 1/4 inch. when washing the salt away, remove all traces to prevent surface discoloration, especially if the concrete is integrally colored. don't apply a sealer until the concrete surface and the small recesses left behind by the salt dry
accordingly, the samples were prepared as follows: 1) dry mix all binder materials for 2 min; 2) place all the mixing water (based on selected w/b) in a bowl; 3) add half the binder and admixtures to the bowl and mix at low speed for 3 min; 4) divide the remaining binder and admixtures into four parts and add the portions (one after the other) to the bowl and mix for 3 min each; 5) fill a
this solution can be used in a carpet cleaning machine or for scrubbing into a carpet with a rag or sponge. after the carpet is dry, vacuum up the remaining residue. household cleaner take ½ cup of any all-purpose household cleaner without bleach, 1 cup of
give it five minutes to dry and then sweep it with a nylon-bristle concrete broom. do this in a direction that is 90 degrees to foot traffic; this will prevent people from slipping. wait 20
soda blasting is a great way to remove paint from large areas of concrete. paint stains on concrete completely disappear using this method, leaving you with a clean surface for repainting if necessary. soda blasting is also an environmentally friendly way to remove paint from concrete, and causes no damage to the underlying concrete.
this seems to be a common problem for people who use fabric softener in their top-loading washing machines. you can look for alternatives to fabric softener: vinegar; wool balls; baking soda. if the problem of the brown flakes is the fabric softener you use,
very effective at plaster pool spot removal, but slow for large stained areas. localized stains can be removed with a gallon of acid magic and a piece of pvc pipe. pour a few cups of acid magic (or use dry acid, aka ph reducer) into a length of 1.5″ pvc pipe that you hold over a small spot on a
avoid leaving your pole lying on the ground when it is delivered. you should raise the pole as soon as possible. until you do, leave it in whatever protective wrapping it arrives in. avoid leaving it lying flat. stand it up and keep it dry until you are ready to install it. 3. small hole size. don't dig the hole for your flagpole installation too small.
it doesn't do much for the actual visibility of the stains, but these are stains that any normal person would have just ripped up the carpet and started over. i've gotten over that. it's not my house and i'm already paying a couple thousand a month in rent i'm just trying to deal with the smell, and the smell on the stairs is
apply stain remover, enzyme cleaner, and/or heavy-duty detergent to the stain as a pretreatment for about 30 minutes. for those stubborn stains, soak in bleach if garment can handle it. using vinegar and boiling water can also be used to remove stains from non-synthetic fabrics.
white residue? here are a few ways to fi nd out: • collect some of the white residue and add a few drops of vinegar to it. if the residue is calcium carbonate (hard-ness), it will foam and dissolve. if it does not dissolve, it may be due to a faulty dip tube in your hot water
lower the dry well into the hole after wrapping the sides with a special silt blocking landscape fabric. to tuck the fabric under the dry well top cover, loosen the screws, push an inch of fabric under the cover, then re-tighten the screws. once it's lowered into place, insert the top drain fitting and make sure it's level with the surrounding soil.
concrete does not need to dry out in order to harden as commonly thought. the concrete (or specifically, the cement in it) needs moisture to hydrate and cure (harden). when concrete dries, it actually stops getting stronger. concrete with too little water may be dry but is not fully reacted.
approach 2: soak in vinegar. white vinegar is an excellent solution for removing pesky deodorant stains from both white and colorful clothing. start by mixing four cups of warm water with one cup of white vinegar. apply the solution to the affected area and use your knuckles to
when the water evaporates, it leaves the calcium, magnesium, or iron salts that are in the water wherever they lie. you can clean that off with acid (not a great idea) or chelants. if you soften the water, you'll leave sodium chloride (salt) behind.
increases in temperature from 21°c (70°f) to 38°c (100°f) may reduce air content by 25% while reductions from 21°c (70°f) to 5°c (40°f) may increase air content by as much as 40%. concrete mixer. the amount of air entrained by any given mixer (stationary, paving, transit) will decrease as
concrete does not require much water to achieve maximum strength. but a wide majority of concrete used in residential work has too much water added to the concrete on the job site. this water is added to make the concrete easier to install. this excess water also greatly reduces the strength of the concrete.
a high pressure hose can be used to remove dirt stains, or a stiff brush and detergent may be used for hard-to-remove stains. use clean water to completely wash everything that has been submerged under water. after everything has been washed using the plain water, repeat using a
urine stains spread 2-4 times their surface size as it soaks into padding. urine-off must contact all urine-affected areas to remove odor and stain. allow to air dry - do not scrub. for old, dried deposits, it may be necessary to repeat application on subsequent days to break down old urine crystals and remove stain
try pure peroxide ore mixed with cream tartar. rub it in let it stand a few minutes, blot it with clean rag, rinse spot with moist rag and depending on size and how heavy stain is put a dry clean towel/rag over it with weight to absorb excess and let it dry. this is likely to be more effective than clothing cleansers.
sludge becomes dried sludge after passing through the sludge drier. bulky wastes are crushed in the crusher. these will be added to the burning/melting furnaces by the cranes and the conveyor. tires and infectious wastes are added to the furnaces using a special lift. the burning/melting operation
